rear engine

英 [rɪə(r) ˈendʒɪn] 美 [rɪr ˈendʒɪn]

网络  后置引擎; 后置发动机; 后置式发动机

机械



双语例句

  1. Even the Volkswagen rear engine car was anticipated by a1904 patent for a cart with the horse at the rear.
    甚至1904年马在车后的马车专利已经预见到了发动机后置的德国“大众”轿车的出现。
  2. Remove rear engine cable carrier.
    拆下后发动机电缆托架。
  3. The net is cast at the rear of the boat and troll for a long distance before it is lifted up using the boat's trolley engine.
    渔夫将网从船后抛进海里,然后拖着一段距离再用引擎拉上来。
  4. There is also additional protection over the top rear engine decks against attack from petrol bombs.
    这里也有附加的装甲保护覆盖后置发动机舱面的顶部对抗来自汽油炸弹的攻击。
  5. The mixing structure is composed of the mixing chamber, front and rear rotor shafts and transverse sealed device, which are fixed to the engine seat by two support seats.
    混练机构由混炼室,前、后转子轴及端面密封装置等构成,通过两个支撑座固定于机座上。
  6. It's shorter in front and its long rear hood is much lower because a bank of batteries has replaced the huge diesel engine.
    它前部较短,尾部很长的发动机罩非常低,因为一组蓄电池取代了体积庞大的柴油发动机。
  7. In the forward fuselage a Daimler-Benz DB603 featured an annular-ring cowl, while exhaust stubs just aft of the trailing edge belied the position of the rear engine.
    在机身前部安置一台具有环形整流罩的戴姆勒-奔驰(Daimler-Benz)DB603型发动机,同时排气管配置在尾部后发动机位置的后面。
  8. The rear rack is square framework above which injector apparatus, cylinder, proportional pressure meter, oil cooler, electric engine and oil pump, etc, are equipped.
    后机架为长方形框架,其上安装有注射装置、油箱、比例压力、流量油路块、油冷却器、电机和油泵等。
  9. Install the new upper rear bearing oil seal with the white paint facing towards the rear of the engine.
    安装新的上后轴承油封,使白漆面向引擎后部。
  10. Secure rear muffler with two metal clips at the engine carrier support.
    用两个金属卡子将尾部消音器固定在发动机托架支架处。
  11. Remove transmission crossmember bolts, and lower rear of engine.
    拆卸变速箱横梁螺栓,并降低引擎后部。
  12. Television pictures showed that three tiles had vanished from the right side of the rear engine cover.
    电视画面表明,有三块瓦片从尾部发动机舱盖右侧脱落。
  13. FEM Analysis of the Abrupt-turning of Low-floor Rear Engine Articulated Bus
    低地板发动机后置式铰接客车急转弯特性有限元分析
  14. Optimum Design for the Cooling Fan in Rear Engine Coach Combined with Cooling and Low Noise
    兼顾冷却和降噪要求的后置客车冷却风扇优化设计
  15. Low Noise Optimization Design of Body Structure for Rear Engine Bus
    发动机后置客车车身结构的低噪声优化设计
  16. But for a abrupt-turning situation FEM analysis is not commonly used for low-floor rear engine articulated bus.
    但是对于发动机后置式铰接客车在急转弯工况下的结构有限元分析,尚不多见。
  17. Study of reduction of noise of the rear diesel engine bus(ⅰ)── test of the noise reducing
    后置柴油机客车的降噪研究(Ⅰ)&降噪试验
  18. An Experimental Study on the Temperature Field in Engine Compartment of a Rear Engine Bus
    后置发动机客车机舱空间温度场的试验研究
  19. The push articulating device is special for the rear engine articulated bus. It possesses particular structure, working principle and electric control system.
    推式铰接装置是可以应用于发动机后置铰接式客车的专用铰接装置,其具有独特的结构、工作原理及电气控制系统。
  20. This paper presents the structure and working principle of an effective oil retaining device used in stead of the front and rear oil seal for engine crankshaft.
    介绍了发动机曲轴前、后端高效拦油装置的结构、工作原理。
  21. Abnormal vibration has been found on rear installation plane in a turbofan engine durability test.
    在某民用涡轮风扇发动机的持久试车过程中,出现了发动机后安装面振动异常的现象。
  22. A study on Rear Mounted Engine Vehicle Cooling System
    后置发动机汽车冷却系统的研究
  23. Power Refitting of Rear Diesel Engine in Bus
    论后置式公交车柴油化动力改装
  24. Improvements and Studies on the Overheat for the Rear-Mounted Diesel Engine on the Large Bus
    后置发动机大客车冷却不足的改进措施与试验研究
  25. Data Collection and Display System Based on CAN-bus of Rear Engine of Coach
    基于CAN总线的客车后置发动机数据采集显示系统
  26. Design of Auto Transmission System with Rear and Cross Mounted Engine
    发动机后横置时汽车传动系的设计
  27. The current domestic large passenger cars and heavy vehicles usually adopt rear mounted engine and manual mechanical transmission.
    目前国内大型客车和重型车辆通常采用后置发动机,使用机械变速操纵系统。
  28. Engine crankshaft front, rear oil seal on the sealing function of crankshaft rotation, which guarantees good lubrication of the engine cylinder body, reduce friction power loss.
    发动机依靠曲轴前、后油封实现对曲轴旋转运动的密封功能,保证了发动机缸体内有良好的润滑,减低摩擦产生的功率损耗。